ST-Link V2 Debug and Programming of ARM STM8 STM32

DescriptionST-Link V2 Debug and Programming of ARM STM8 STM32FeaturesAutomatic upgrades from official ST-Link softwareIndicator LEDs, Red and BlueAluminum Case3.3V and 5V Power Output500mA self-recover fuse to protect your USB Port20cm 4 way F-F Multicolor Jumper cableEasy to useSoftware SupportedST-LINK Utility 2.0 and 4.2.1 aboveSTVD and aboveSTVP 3.2.3 and aboveIAR EWARM V6.20 and aboveIAR EWSTM8 V1.30 and aboveKEIL RVMDK V4.21 and above (Can use Keil MDK 4.60 )STVPST Visual Programmer for programming ST7, STM8 and STM32Keil MDKProduct PageST LinkDownloadIAR STM8’s debug probe Product PageThe ST-LINK/V2 is an in-circuit debugger and programmer for the STM8 and STM32 microcontroller families. The single wire interface module (SWIM) and JTAG/serial wire debugging (SWD) interfaces are used to communicate with any STM8 or STM32 microcontroller located on an application board.STM8 applications use the USB full speed interface to communicate with STMicroelectronic’s ST Visual Develop (STVD) or ST Visual Program (STVP) software.STM32 applications use the USB full speed interface to communicate with Atollic, IAR, Keil or TASKING integrated development environments.Key Features3.3V or 5V power supplied by a USB connectorUSB 2.0 full speed compatible interfaceSWIM specific featuresSWIM cable for connection to the application via a pin header or a 2.54 mm pitch connector1.65 V to 5.5 V application voltage supported on SWIM interfaceSWIM low-speed and high-speed modes supportedSWIM programming speed rate: 9.7 Kbytes/s in low speed and 12.8 Kbytes/s in high speedSWIM cable for connection to the applicationDirect firmware update feature supported (DFU)Status LED which blinks during communication with the PCOperating temperature 0 to 50 °CSupported DevicesMicrocontrollers supported by STVP release 3.2.8:Product lineMicrocontrollerSTM32STM32F100xx, STM32F101xx, STM32F102xx, STM32F103xx, STM32F105xx, STM32F107xx, STM32F2xxx, STM32F4xxx,STM32L15xx6, STM32L15xx8,STM32L15xxB, STM32L151xC, STM32L151xD, STM32L152xC, STM32L152xD, STM32L162xD,STM32TS60,STM32W108C8, STM32W108xB, STM32W108xC, STM32W108xZSTM8STM8AF51x, STM8AF52x, STM8AF61x, STM8AF62x,STM8AH51x, STM8AH61x,STM8S003K3, STM8S003F3, STM8S005C6, STM8S005K6, STM8S007C8, STM8S103xx, STM8S105xx, STM8S207xx, STM8S208xx, STM8S903F3, STM8S903K3,STM8L101xx, STM8L15x, STM8L16x,STM8TL52x4,STM8TL53x4SW DRIVERSWhile connecting the ST-LINK/V2 to the computer through USB interface, the USB driver is required and should be installed correctly first.Click on the link below to download:ST-LINK/V2 USB driver for Windows 7, Vista and XP